![Craftsman 5 horsepower track snowblower](https://kumkoniak.com/57.jpg)
If your gas blower is shaky or jittery when it’s on, there may be a problem with fuel combustion. Changing a belt on a larger two-stage machine involves dismantling the unit to gain access to the flywheel, a job best left to a service professional.Īnd if you want to avoid trekking to a store in a snowstorm, it’s a good idea to always have a replacement belt (and extra shear pins) on hand throughout the season. Replace a suspect belt by pulling the wheel off, then the belt, and adding the replacement part in reverse order. Between uses, remove the cover and check the belt for cracks. The friction required to engage the auger belt on a single-stage snow blower tends to wear a belt down faster than on two-stage machines. The problem is unique to single-stage blowers because their augers make direct contact with the ground, unlike two- or three-stage blowers, which have augers that don’t touch the ground.
![craftsman 5 horsepower track snowblower craftsman 5 horsepower track snowblower](https://canton-hoy.com/images/8526a856fee7b35ca41c15f3a94f43ad.jpg)
#CRAFTSMAN 5 HORSEPOWER TRACK SNOWBLOWER WINDOWS#
Caution: Keep in mind that you shouldn’t run a single-stage snow blower over gravel because it can pick up and throw the gravel with the snow, possibly damaging windows or injuring passersby. (Check with the store where you bought the machine, or search by brand at Snow Blowers Direct to order one online.) Adjust the new bar to be about ⅛ inch above the ground. Prop the snow blower up and remove the bolts that hold the bar to the housing, and replace it with a new one. Running over concrete, asphalt, and gravel can wear the metal down, leaving furrows of snow behind. The Problem: The Machine Leaves Too Much Snow BehindĪ flat metal bar on the underside of the machine chisels snow and ice off the ground and into the auger. After adjusting the cables, be sure to spray some lubricant at the pivot points of any moving parts. Adjust again as necessary until the lurching stops. Unclip the cable from the handle and snug up the line’s threaded adjustment at the base of the machine, then reconnect the clip and test the handling. If you squeeze the drive handle and the snow blower jerks forward, you’ll need to tighten the line. Over time, the cables that send power to the wheels need to be adjusted to apply proper tension to the belt on two-stage snow blowers.
![craftsman 5 horsepower track snowblower craftsman 5 horsepower track snowblower](https://www.bluegreenish.com/wp-content/uploads/2018/07/craftsman-8-26-track-drive-snowblower-manual.jpg)
The Problem: The Snow Blower Is Difficult to Maneuver or Lurches Forward Use a clearing tool or broom handle to clear the clog-never your hands or feet, even if you’re wearing gloves: A stationary auger and impeller are often under enough belt tension to harm hands and feet, even with the engine or electric motor off. Turn off the engine of a gas snow blower or unplug the cord, or remove the battery, of an electric model. The Problem: The Auger or Discharge Chute Is Clogged For electric models, make sure the tool is plugged in or that the battery is fully charged. Use a gas siphon to drain the gas from the blower, then refuel with fresh stabilized gasoline and try again. Otherwise, if the gas is more than 30 days old, ethanol in the fuel may have caused moisture to build up in the fuel system. If the gas blower has an electric starter, make sure the blower is plugged into an outlet.
![craftsman 5 horsepower track snowblower craftsman 5 horsepower track snowblower](https://images.offerup.com/agtXhNFLieLE84Mzi9n1VJHn_cI=/600x1066/9583/95832dcfec164c749cd28beacaa1b6f9.jpg)
If you have a gas model, first check to see whether there’s gas in the tank.
![Craftsman 5 horsepower track snowblower](https://kumkoniak.com/57.jpg)